TLE4296-2 Low Drop Voltage Regulator TLE4296-2GV33 TLE4296-2GV50 Data Sheet Rev. 1.13, 2014-03-18 Automotive Power

Low Drop Voltage Regulator TLE4296-2GV33 TLE4296-2GV50 1 Overview Features • Two versions: 3.3V, 5.0V • Output voltage tolerance ≤ ±4% • Very low drop voltage • Output current: 30mA • Inhibit input • Low quiescent current consumption • Wide operation range: up to 45V • Wide temperature range: T = -40 °C to +150 °C j PG-SCT595 • Output protected against short circuit • Overtemperature protection • Reverse polarity proof • Very small SMD-Package PG-SCT595 • Green Product (RoHS compliant) • AEC Qualified Description The TLE4296-2 is a monolithic integrated low-drop voltage regulator in the very small SMD package PG-SCT595. It is designed to supply e.g. microprocessor systems under the severe conditions of automotive applications. Therefore the device is equipped with additional protection functions against overload, short circuit and reverse polarity. At overtemperature the regulator is automatically turned off by the integrated thermal protection circuit. Input voltages up to 40V are regulated to V = 3.3V (V33 version) or 5.0V (V50 version). The output is able Q,nom to drive a load of more than 30mA while it regulates the output voltage within a 4% accuracy. To save energy the device can be switched in stand-by mode via an inhibit input which causes the current consumption to drop below 5μA. Type Package Marking TLE4296-2GV33 PG-SCT595 C5 TLE4296-2GV50 PG-SCT595 C4 Data Sheet 2 Rev. 1.13, 2014-03-18

TLE4296-2 Block Diagram 2 Block Diagram Temperature Saturation Control Control and Protection Circuit 3 4 Ι Q Band-Gap- + Referenz 1 2,5 INH GND AEB02312 Figure1 Block Diagram Data Sheet 3 Rev. 1.13, 2014-03-18

TLE4296-2 Pin Configuration 3 Pin Configuration 3.1 Pin Assignment 5 4 1 2 3 SCT595.vsd Figure2 Pin Configuration (top view) 3.2 Pin Definitions and Functions Pin Symbol Function 1 INH Inhibit Input: high level to turn on the IC 2 GND Ground: connected to pin 5 3 I Input Voltage 4 Q Output voltage: must be blocked with a ceramic capacitor C ≥ 3.3µF, ESR ≤ 2Ω Q 5 GND Ground: Connected to pin 2 Data Sheet 4 Rev. 1.13, 2014-03-18

TLE4296-2 General Product Characteristics 4 General Product Characteristics 4.1 Absolute Maximum Ratings Absolute Maximum Ratings1) T = -40 °C to +150 °C; all voltages with respect to ground, positive current flowing into pin j (unless otherwise specified) Pos. Parameter Symbol Limit Values Unit Conditions Min. Max. Input 4.1.1 Voltage V -42 45 V – I 4.1.2 Current I – – mA 2) I Output 4.1.3 Voltage V -0.3 30 V – Q 4.1.4 Current I – – mA 2) Q Inhibit 4.1.5 Voltage V -42 45 V – INH 4.1.6 Current I -500 2) μA – INH 4.1.7 Current I -5 5 mA -0.3V ≤ V ≤ 45V ; INH I t < 1ms p Temperatures 4.1.8 Junction Temperature T -40 150 °C – j 4.1.9 Storage Temperature T -50 150 °C – stg Thermal Resistance 4.1.10 Junction Pin R – 30 K/W Measured to pin 5 thj-pin 4.1.11 Junction ambient3) R – 179 K/W Zero airflow ; thja zero heat sink area 1) Not subject to production test, specified by design. 2) Internally limited 3) Worst case regarding peak temperature Note:Stresses above the ones listed here may cause permanent damage to the device. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Note:Integrated protection functions are designed to prevent IC destruction under fault conditions described in the data sheet. Fault conditions are considered as “outside” normal operating range. Protection functions are not designed for continuous repetitive operation. Data Sheet 5 Rev. 1.13, 2014-03-18

TLE4296-2 General Product Characteristics 4.2 Functional Range Table1 Example 1 for Functional Range - use only for MOSFET and Voltage Linear Regulator Pos. Parameter Symbol Limit Values Unit Conditions Min. Max. 4.2.1 Input Voltage V 4.0 45 V TLE4296-2GV33 I 4.2.2 5.5 45 V TLE4296-2GV50 4.2.3 Inhibit Voltage V -0.3 40 V – INH 4.2.4 Junction Temperature T -40 150 °C – j Note:Within the functional or operating range, the IC operates as described in the circuit description. The electrical characteristics are specified within the conditions given in the Electrical Characteristics table. Data Sheet 6 Rev. 1.13, 2014-03-18

TLE4296-2 Electrical Characteristics 5 Electrical Characteristics 5.1 Electrical Characteristics Voltage Regulator Electrical Characteristics V = 13.5 V; V > 2.5V; T = -40 °C to +150 °C; all voltages with respect to ground (unless otherwise I INH j specified) Pos. Parameter Symbol Limit Values Unit Measuring Condition Min. Typ. Max. 5.1.1 Output Voltage V 3.17 3.3 3.43 V 1mA ≤ I ≤30mA Q Q 5.1.2 TLE4296-2GV33 3.17 3.3 3.43 V I =10mA ; Q 4.3V ≤ V ≤40 V I 5.1.1 Output Voltage V 4.80 5.00 5.20 V 1mA ≤ I ≤30mA Q Q 5.1.2 TLE4296-2GV50 4.80 5.00 5.20 V I =10mA ; Q 6V ≤ V ≤40 V I 5.1.3 Output Current Limitation I 30 – – mA 1) Q 5.1.4 Dropout Voltage 1) V – 250 300 mV I =20mA dr Q 5.1.5 Output capacitor C 3.3 – – μF ESR ≤2Ω at 10kHz Q 5.1.6 Current Consumption I – 2 5.2 mA I <30mA q Q 5.1.7 Iq=II–IQ – 130 170 μA IQ<0.1mA ; Tj < 85°C 5.1.8 Quiescent Current (stand-by) I – – 1 μA V =0.4V ; T < 85°C q INH j 5.1.9 Iq=II–IQ – – 5 μA VINH=0.4V 5.1.10 Load Regulation ∆V – 17 50 mV 1mA < I <25mA ; Q Q T =25°C ; j TLE4296-2GV50 5.1.11 – 14 40 mV 1mA < I <25mA ; Q T =25°C ; j TLE4296-2GV33 5.1.12 Line Regulation ∆V – 10 25 mV V =(V + 0.5V) Q I Q,nom to 36V ; I =1mA ; T =25°C Q j 5.1.13 Power Supply Ripple PSRR – 60 – dB f =100kHz ; V = 0.5 Vpp r r Rejection Logic Inhibit Input 5.1.14 Inhibit, Turn-on voltage V – – 2.2 V V >0.95*V INH,high Q Q,nom 5.1.15 Inhibit, Turn-off voltage V 0.4 – – V V <0.1V INH,low Q 5.1.16 H-input current I – 8 12 μA V =5V INH,high INH 5.1.17 L-input current I -2 – 2 μA V =0V INH,low INH 1) Measured when the output voltage V has dropped 100mV from the nominal value. Q Data Sheet 7 Rev. 1.13, 2014-03-18

TLE4296-2 Electrical Characteristics 5.2 Typical Performance Characteristics Voltage Regulator Output Voltage V vs. Current Consumption I vs. Q q Input Voltage V Input Voltage V I I AED03349.VSD AED03347.VSD 10 1000 VQ V VRIN H= =1 5k ΩV Iq µA VINH = 5 V L 8 800 6 600 GV50 4 400 R = 1 kΩ L GV33 2 200 R = 5 kΩ L 0 0 0 2 4 6 8 V 10 0 10 20 30 40 V 50 V V I I Data Sheet 8 Rev. 1.13, 2014-03-18

TLE4296-2 Application Information 6 Application Information Note:The following information is given as a hint for the implementation of the device only and shall not be regarded as a description or warranty of a certain functionality, condition or quality of the device. VQ,nom+ 0.5V to 45V Ι Q 3.0V / 3.3V / 5.0V 3 4 C C Ι Q TLE 4296-2G μ 100 nF 4.7 F Inhibit INH e.g. TDK 1 C3216X7R1C475M 2,5 GND AES02313_4296-2 Figure3 Application Diagram In the TLE4296-2 the output voltage is divided and compared to an internal reference of 2.5V typical. The regulation loop controls the output to achieve a stabilized output voltage. Figure3 shows a typical application circuit. In order to maintain the stability of the control loop the TLE4296-2 output requires an output capacitor C of at least 3.3μF with a maximum permissible ESR of 2Ω. It is Q recommended to use a multi layer ceramic capacitor for C , e.g. the TDK C3216X7R1C475M with a nominal Q capacitance of 4.7μF. Aluminum electrolytic as well as tantalum capacitors do not cover the required ESR range over the full operating temperature range of T = -40 °C to +150 °C. j At the input of the regulator an input capacitor is necessary for compensating line influences (100nF ceramic capacitor recommended). A resistor of approx. 1Ω in series with C, can damp any oscillation occurring due the I input inductivity and the input capacitor. If the regulator is sourced via long input lines of several meters it is recommended to place an additional electrolytic capacitor ≥ 47μF at the input. Data Sheet 9 Rev. 1.13, 2014-03-18

TLE4296-2 Package Outlines 7 Package Outlines 2.9±0.2 B (2.2) (1.45) +0.1 1.2 -0.05 (0.3) 1.1 MAX. 1) (0.4) 0.1 MAX. 5 4 (0.13) 1)(0.23) 1 2 3 +0.1 2.5±0.1 0.25±0.1 0˚ MAX. 0˚ MAX. 1.6±0.1 0.3-0.05 1 1 A +0.1 0.15 0.6+0.1 -0.06 -0.05 0.95 0.2 M A 1.9 1) Contour of slot depends on profile 0.25 M B of gull-wing lead form GPW05997 Figure4 PG-SCT595 (Plastic Small Outline) Green Product (RoHS compliant) To meet the world-wide customer requirements for environmentally friendly products and to be compliant with government regulations the device is available as a green product. Green products are RoHS-Compliant (i.e Pb-free finish on leads and suitable for Pb-free soldering according to IPC/JEDEC J-STD-020). For further information on alternative packages, please visit our website: http://www.infineon.com/packages. Dimensions in mm Data Sheet 10 Rev. 1.13, 2014-03-18

TLE4296-2 Revision History 8 Revision History Revision Date Changes Rev. 1.13 2014-03-18 Page5: Typo (introduced in Rev. 1.11) in Unit of parameter 4.1.6 corrected from A to μA. No change of the device or test limits. Rev. 1.12 2011-05-11 Page2: Current Consumption in Standby corrected from 5mA to 5μA in the Functional Description. Value in Electrical Characteristics is still correct. Rev. 1.11 2011-02-10 Page2: Marking added. Page1: Coverpage added. All Pages: New Infineon Data Sheet Layout applied. Rev. 1.1 2008-01-28 Initial version of RoHS-compliant derivate of TLE 4296-2 Page2: AEC certified statement added. Page2 and Page10: RoHS compliance statement and Green product feature added. Page2 and Page10: Package changed to RoHS compliant version. Legal Disclaimer updated Rev. 1.0 2004-01-01 Final Data Sheet Data Sheet 11 Rev. 1.13, 2014-03-18

Edition 2014-03-18 Published by Infineon Technologies AG 81726 Munich, Germany © 2014 Infineon Technologies AG All Rights Reserved. Legal Disclaimer The information given in this document shall in no event be regarded as a guarantee of conditions or characteristics. With respect to any examples or hints given herein, any typical values stated herein and/or any information regarding the application of the device, Infineon Technologies hereby disclaims any and all warranties and liabilities of any kind, including without limitation, warranties of non-infringement of intellectual property rights of any third party. Information For further information on technology, delivery terms and conditions and prices, please contact the nearest Infineon Technologies Office (www.infineon.com). Warnings Due to technical requirements, components may contain dangerous substances. For information on the types in question, please contact the nearest Infineon Technologies Office. Infineon Technologies components may be used in life-support devices or systems only with the express written approval of Infineon Technologies, if a failure of such components can reasonably be expected to cause the failure of that life-support device or system or to affect the safety or effectiveness of that device or system. Life support devices or systems are intended to be implanted in the human body or to support and/or maintain and sustain and/or protect human life. If they fail, it is reasonable to assume that the health of the user or other persons may be endangered.

Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: I nfineon: TLE4296-2G V33 TLE4296-2G V50 TLE42962GV50HTSA1 TLE42962GV33HTSA1